amphenol代理商
专业销售Amphenol(安费诺)全系列产品-英国2号仓库
库存查询
美国1号分类选型新加坡2号分类选型英国10号分类选型英国2号分类选型日本5号分类选型

在本站结果里搜索:    
热门搜索词:  Connectors  8910DPA43V02  Amphenol  UVZSeries 160VDC  70084122  IM21-14-CDTRI

MP9100-0.15-1% - 

Resistor; Thick Film; Res 0.15 Ohms; Pwr-Rtg 100 W; Tol 1%; Radial; TO-247; Heat Sink

Caddock MP9100-0.15-1%
声明:图片仅供参考,请以实物为准!
制造商:
Caddock Caddock
制造商产品编号:
MP9100-0.15-1%
仓库库存编号:
70089431
技术数据表:
View MP9100-0.15-1% Datasheet Datasheet
订购热线: 400-900-3095  0755-21000796, QQ:800152669, Email:sales@szcwdz.com
由于产品数据库庞大,部分产品信息可能未能及时更新,下单前请与销售人员确认好实时在库数量,谢谢合作!

MP9100-0.15-1%产品概述

Power Film Resistors, Radial Leaded Termination, Heat Sink Mountable Design, Kool-Pak®
Temperature Coefficient:
MP915, MP916, MP925, MP930, MP850:
ΔR taken at +150°C, ref. to 25°C
0.500 ohm to 100 K, –20 to +80 ppm/°C
0.050 ohm to 0.499 ohm: 0 to +200 ppm/°C
0.020 ohm to 0.049 ohm: 0 to +300 ppm/°C
0.010 ohm to 0.019 ohm: 0 to +500 ppm/°C
MP9100:
ΔR taken at +175°C, ref. to +25°C
0.500 ohm to 100 ohm: –20 to +80 ppm/°C
0.050 ohm to 0.49 ohm: 0 to +150 ppm/°C
Measurement Note:
For these specifications, resistance measurement shall be made at a point on the leads 0.2" (5 mm) from the package.
The Thermal Design Should Satisfy the Following Equation:
Case Temperature (Tc) + [Thermal Resistance (Rφjc) × Power Applied (Watts)] < Tmax, considering the full operating temperature range of the application.
Mounting Note:
Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such as thermal grease. The entire exposed heat dissipating mounting surface (ceramic or metal) must be in contact with the heat sink. When screw mounting, use a compression washer which provides a mounting force of 150 to 300 pounds (665 to 1330 N). This will provide sufficient pressure on the package over time and through large temperature variations to maintain the maximum power dissipation capability. Maximum mounting torque to avoid package damage is 8 in.-lbs (0.9 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center of the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small point of the plastic body. Another mounting option is to use a pressure bar method, which can achieve a greater mounting force with greater contact area.
Features
  • Non-Inductive Design, Ideal for Power Switching Circuits, Snubbers, RF Applications:
    50 Ohm Performance Up to 500 MHz
  • Values as Low as 0.010 Ohm Ideal for Current Sensing in Power Supplies, Motor Controls, and Battery Circuits
  • Resistor Element Electrically Isolated from the Heat Dissipating Mounting Surface (1500 Volts rms AC)
  • 1% Tolerance for Most Values
  • MP9100-0.15-1%产品信息

      Brand/Series  Kool-Pak MP9000 Series  
      Material, Element  Thick Film  
      Package Type  TO-247  
      Power Rating  100 W  
      Resistance  0.15 Ohms  
      Special Features  Heat Sink  
      Termination  Radial Leads  
      Tolerance  ±1 %  
    关键词         
    电话:400-900-3095
    QQ:800152669
    关于我们 | Amphenol简介 | Amphenol产品 | Amphenol产品应用 | Amphenol动态 | 按系列选型 | 按产品规格选型 | Amphenol选型手册 | 付款方式 | 联系我们
    Copyright © 2017 www.amphenol-connect.com All Rights Reserved. 技术支持:电子元器件 ICP备案证书号:粤ICP备11103613号